- 您现在的位置：买卖IC网 > Sheet目录368 > W25Q80BWSSIG (Winbond Electronics)IC FLASH SPI 8MBIT 8SOIC
W25Q80BW
7.2.24
32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “52h” followed a 24 -bit block address (A23-A0) (see Figure 2). The Block
Erase instruction sequence is shown in figure 22.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of t BE 1 (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of
the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB,
BP2, BP1, and BP0) bits (see Status Register Memory Protection table).
/CS
Mode 3
0
1
2
3
4
5
6
7
8
9
29
30
31
Mode 3
CLK
Mode 0
Instruction (52h)
24-Bit Address
Mode 0
DI
(IO 0 )
23
*
22
2
1
0
DO
(IO 1 )
* = MSB
High Impedance
Figure 22. 32KB Block Erase Instruction Sequence Diagram
- 42 -
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
W25X40BVZPIG
IC SPI FLASH 4MBIT 8WSON
W25X64VZEIG
IC FLASH 64MBIT 75MHZ 8WSON
W25X80AVDAIZ
IC FLASH 16MBIT 100MHZ 8DIP
W29GL032CB7A
IC FLASH 32MBIT 70NS 48TFBGA
W29GL064CB7S
IC FLASH 64MBIT 70NS 48TSOP
W29GL128CL9T
IC FLASH 128MBIT 90NS 56TSOP
W631GG6KB-15
IC DDR3 SDRAM 1GBIT 96WBGA
W9412G6IH-5
IC DDR-400 SDRAM 128MB 66TSSOPII
相关代理商/技术参数
W25Q80BWSSIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80BWUXIG
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80BWUXIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80BWZPIG
功能描述:IC FLASH SPI 8MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q80BWZPIG TR
功能描述:IC FLASH SPI 8MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP（0.465"，11.8mm 宽） 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8
W25Q80BWZPIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25S243A
制造商:WINBOND 制造商全称:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25S243A-12
制造商:WINBOND 制造商全称:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM